- Kitronik e-textiles teaching resources.
- Kitronik electronic kit teaching resources.
- 3rd party teaching resources.
- DXF cutting files.
- Autodesk models.
Kitronik E-Textiles Teaching Resources
-
27xx - Sewable LED kit resources
The sewable LED kits allow a number of LEDs to be added to a textiles project. Teaching Resources.
Kitronik Electronic Kit Teaching Resources
-
2101 - Alarm kit
Using a dual 555 timer this kit is an alarm with exit delay and silencing timer. Teaching Resources.
-
2102 - Battery tester kit
The battery tester uses an op amp IC to generate 3 battery level thresholds shown on LEDs. Teaching Resources.
-
2103 - Game kit
The game kit has a pre-programmed PIC which gives a memory & reactions game in one. Teaching Resources.
-
2104 - Timer kit
A dual 555 timer is used to turn on an LED for a period after which a buzzer sounds. Teaching Resources.
-
2105 - Xylophone kit
The xylophone kit has a pre-programmed PIC which plays notes when the keys are pressed. Teaching Resources.
-
2106 - Rear bike light kit
Two high brightness red LEDs flash alternatively to making a rear bike light. Teaching Resources.
-
2107 - Terminal block steady hand
The terminal block steady hand game, requires no soldering. Teaching Resources.
-
2108 - Steady hand with latch
A simple board allows an LED to be latched when the loop touches the track. Teaching Resources.
-
2109 - Electronic dice kit
Using a pre-programmed PIC the LEDs randomly show a number when the button is pressed. Teaching Resources.
-
2110 - Thermometer kit
The LEDs on the thermometer light to show the temperature. Teaching Resources.
-
2111 - Easy build timer kit
When the button is pressed the LED changes colour for a given delay. Teaching Resources.
-
2112 - Light activated switch
This board allows an LED or other electronic device to switch on light or dark. Teaching Resources.
-
2113 - Heat activated switch
This board allows an LED or other electronic device to switch on hot or cold. Teaching Resources.
-
2114 - Mini torch kit
The mini torch is a simple kit containing a battery, switch and bright white LED. Teaching Resources.
-
2115 - Discontinued - MP3 amplifier kit
These notes are for use with the old mono amplifier kit. All new purchases will be for stock code 2154 later in the page. Teaching Resources.
-
2116 - Quiz buzzer kit
The quiz buzzer indicates which of two people was first to press their button. Teaching Resources.
-
2117 - Square wave generator kit
This kit generates a square wave, which when connected to a speaker makes a tone. Teaching Resources.
-
2118 - Seven segment counter kit
The display shows a number 0 to 9 and can be counted up or down. Teaching Resources.
-
2119 - Colour LED & battery box
A single sheet detailing how to connect a colour LED to a battery box. Teaching Resources.
-
2120 - Colour changing night light
The LED automatically turns on when it goes dark and cycles through various colours. Teaching Resources.
-
2121 - Programmable timer
This timer can be programmed to set the duration and how the LED & buzzer work. Teaching Resources.
-
2122 - Programmable music box
The music box plays a simple tune (chosen by the student) when the switch is activated. Teaching Resources.
-
2123 - Air freshener kit
When the button is pressed the fan runs for a period of time. Teaching Resources.
-
2124 - Motor controller
This board can be programmed to drive two motors with forward & reverse control. Teaching Resources.
-
2125 - Cut it yourself tank kit
Self assembly tank kits, fully programmable by adding a motor controller board. Teaching Resources.
-
2126 / 2127 - PIC dev / project
The PIC boards have 2 inputs & 3 outputs that can be used as needed for any project. Teaching Resources.
-
2131 - Colour USB lamp kit
This board allows a colour changing LED to be powered from a PCs USB port. Teaching Resources.
-
2132 - White USB lamp kit
This board allows a white LED to be powered from a PCs USB port. Teaching Resources.
-
2133 - Light up decoration
This set of instructions show to cut the plastic and assemble the electronics. Teaching Resources.
-
2134 - Solar garden light kit
This white light turns on at night and charges during the day. Teaching Resources.
-
2135 - FM radio kit
Tune in to your favourite radio stations with this FM radio kit. Teaching Resources.
-
2136 - Stereo amplifier
This stereo amplifier uses a TBA2822M IC to give 1W per channel. Teaching Resources.
-
-
2139 - Timed night light
A light that turns on at dusk and then automatically turns off after up to half an hour. Teaching Resources.
-
2140 - Wireless steady hand game
With this steady hand game the person using the game is the wire connection to the loop. Teaching Resources.
-
2141 - Deluxe stereo amplifier
A deluxe version of the amplifier with volume control, power socket & power switch. Teaching Resources.
-
2142 - Sound meter
The microphone on this kit detects noise and the louder it is the more LEDs light. Teaching Resources.
-
2143 - High power amplifier
This amplifier kit can output up to 15W per channel into a pair of high quality speakers. Teaching Resources.
-
2144 - Relay board
This easy to configure board allows most sensors to activate a relay output. Teaching Resources.
-
2145 - Coin cell power board
This simple kit offers a compact alternative to using two AA batteries. Teaching Resources.
-
2146 - LED picture frame
This kit allows you to illuminate the edge of a picture frame using a number of LEDs. Teaching Resources.
-
2147 - Shower water saver timer
Reduce the amount of water used when showering with this timer. Teaching Resources.
-
-
-
-
2152 - Micro USB lamp kit with 1W LED
Reuse an old phone charger to to power this desk lamp via the micro USB connector. Teaching Resources.
-
2153 - Solar powered buggy
A mechanical buggy kit, that moves using the power of the sun. Teaching Resources.
-
2154 - MP3 amplifier kit
The mono amplifier kit uses anLM386 to drive a speaker for use with MP3 players. Teaching Resources.
-
2155 - 5V LED Desk Lamp Kit
This 5V LED lamp module offers a really bright light, which is compact and easy to mount. It can be run from a 5V power supply and outputs around 16,000 mCd. Teaching Resources.
-
2156 - Bump and Spin Kit
This board allows a buggy to be controlled; it can be programmed so that when it bumps in to something it reverses and spins. Teaching Resources.
-
2157 - FM Radio Kit V2.0
The FM Radio has controls for tuning and to adjust the volume. Includes an audio amplifier and output is via a 66mm speaker. Powered by batteries or mains. Teaching Resources.
-
2158 - 3W Class D Stereo Amplifier
This Class D Amplifier Kit can output up to 3W in total. It runs from 3.2V to 5.5V, and comes with a 3.5mm jack lead and 2 full range speakers. Teaching Resources.
-
2159 - Bump and Spin Buggy Kit
Bump and Spin buggy is an excellent introduction to robotics and programming using the popular PICAXE 08M2 chip. Teaching Resources.
-
2160 - Bluetooth Stereo Amplifier Kit
This amplifier kit can output up to 15W per channel into a pair of high quality speakers. Teaching Resources.
-
2161 - Micro USB Lamp Kit - 1W LED V2.0
This kit allows you to build a mains powered lamp that takes power from a standard Micro USB phone charger. It uses a very bright 1W Power LED. Teaching Resources.
-
2162 - USB Fan Kit
This kit allows you to build a mains powered lamp that takes power from a standard Micro USB phone charger. It uses a very bright 1W Power LED. Teaching Resources.
-
2163 - Learning to solder LED kit, Pack of 25
The Learn To Solder pack is a cost effective way to teach soldering to a class of 25 that results in a testable product. Backed up by colour step by step guides. Teaching Resources.
-
2164 - Wind-up Torch Kit
Our windup torch Kit is a great way learn about both electronics & alternive power sources and results in ahighly useful finished item. No batteries required! Teaching Resources.
-
2165 - Mono Amplifier Version 3.0
MP3 Mono Audio Amplifier Kit: supplied with a pre-built jack cable, an 8ohm 66mm speaker, and a AA battery pack, and uses an NCP2890 audio amplifier IC. Teaching Resources.
3rd Party Teaching Resources
-
3723 - Picaxe Cyberpet kit
The cyberpet is programmed to make an electronic pet which responds to light or touch. Teaching Resources.
-
3724- Picaxe Alarm kit
A simple alarm can be made using the two inputs and LED and sounder outputs. Teaching Resources.
-
3725 - Picaxe Dice kit
Program this board to show a dice number when the switch is pressed. Teaching Resources.
-
3707- Picaxe Proto-Board kit
The PICAXE-08 proto board allows simple projects to be built. Teaching Resources.
-
3708 - Picaxe-18 Project Board kit
The board has 5 inputs and 8 outputs with Darlington drivers. Teaching Resources.
-
3718 - Picaxe-20 Project Board kit
The 20 pin board has 8 inputs and 8 outputs, perfect for larger projects. Teaching Resources.
-
2115BB - Boombox
The Boombox is designed to work with our Mono Amplifier kit. Boombox Presentations. -
4501 - Stem Racer
The STEM racer allows students to investigate the effect of simple decisions. Scheme of Work.
DXF Cutting Files
-
2125 - Laser Cut it Yourself Tank kit
The Tank Kit uses the Motor Controller Board to drive two Bidirectional Motors, allowing the tank to move forward, backwards or spin on the spot. Cutting Files. -
-
2143 - High Power Amplifier Case Cutting Files
Cutting files for our High Power Amplifier kit. Cutting Files. -
-
Autodesk Models
-
2115 - MP3 amplifier kit
The mono amplifier kit uses a TBA820 to drive a speaker for use with MP3 players. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files. -
2136 - Stereo amplifier
This stereo amplifier uses a TBA2822M IC to give 1W per channel. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files. -
2141 - Deluxe stereo amplifier
A deluxe version of the amplifier with volume control, power socket & power switch. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files. -
2106 - Rear bike light kit
Two high brightness red LEDs flash alternatively to making a rear bike light. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files. -
2131 - Colour USB lamp kit
This board allows a colour changing LED to be powered from a PCs USB port. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files. -
2120 - Colour changing night light
The LED automatically turns on when it goes dark and cycles through various colours. You can use these files if you are using CAD to design a laser cut or 3D printed case. Autodesk Files.
©Kitronik Ltd – You may print this page & link to it, but must not copy the page or part thereof without Kitronik's prior written consent.
2 comments
Rob Haywood
Hi Stefi, We've tried to resolve this but are having issues emailing you. Could you Michael a ring on 0845 838 0781 and he'll get it sorted for you. Rob
stefi
I am trying to open the teaching notes for the 2141 deluxe stereo amp, but it seems impossible. Would you possibly have another way for me to access it? Many thanks and best wishes, Stefi